Product Code Database
The guitar is a stringed musical instrument that is usually fretted (with Fretless guitar) and typically has six or twelve strings. It is usually held flat against the player's body and played by strumming or plucking the strings with the dominant hand, while simultaneously pressing selected strings against frets with the fingers of the opposite hand. A guitar pick may also be used to strike the strings. The sound of the guitar is projected either Acoustics, by means of a resonant hollow chamber on the guitar, or Amplified music by an electronic pickup and an guitar amplifier.
The guitar is classified as a chordophone, meaning the sound is produced by a vibrating string stretched between two fixed points. Historically, a guitar was constructed from wood, with its strings made of catgut. Steel guitar strings were introduced near the end of the nineteenth century in the United States, but nylon and steel strings became mainstream only following World War II. The guitar's ancestors include the gittern, the vihuela, the four-course Renaissance guitar, and the five-course baroque guitar, all of which contributed to the development of the modern six-string instrument.
There are three main types of modern guitar: the classical guitar (Spanish guitar); the steel-string acoustic guitar or electric guitar; and the Hawaiian guitar (played across the player's lap). Traditional acoustic guitars include the flat top guitar (typically with a large sound hole) or the archtop guitar, which is sometimes called a "jazz guitar". The tone of an acoustic guitar is produced by the strings' vibration, amplified by the hollow body of the guitar, which acts as a resonating chamber. The classical Classical guitar is often played as a solo instrument using a comprehensive fingerstyle technique where each string is plucked individually by the player's fingers, as opposed to being strummed. The term "finger-picking" can also refer to a specific tradition of folk, blues, bluegrass, and country guitar playing in the United States.
, first patented in 1937, use a pickup and guitar amplifier that made the instrument loud enough to be heard, but also enabled manufacturing guitars with a solid block of wood, without needing a resonant chamber. A wide array of electronic became possible including reverb effect and distortion (or "overdrive"). Solid-body guitars began to dominate the guitar market during the 1960s and 1970s; they are less prone to unwanted acoustic feedback. As with acoustic guitars, there are a number of types of electric guitars, including hollowbody guitars, (used in jazz guitar, blues and rockabilly) and Solid body, which are widely used in rock music.
The loud, amplified sound and sonic power of the electric guitar played through a guitar amp have played a key role in the development of blues and rock music, both as an accompaniment instrument (playing and chords) and performing , and in many rock subgenres, notably heavy metal music and punk rock. The electric guitar has had a major influence on popular culture. The guitar is used in a wide variety of musical genres worldwide. It is recognized as a primary instrument in genres such as blues, Bluegrass music, country music, flamenco, Folk music, jazz, jota, ska, mariachi, metal, punk rock, funk, reggae, rock music, grunge, Soul music, acoustic music, disco, new wave, new age, adult contemporary music, and pop music, occasionally used as a sample in hip-hop, dubstep, or trap music.
The origins of the modern guitar are not known. Before the development of the electric guitar and the use of synthetic materials, a guitar was defined as being an instrument having "a long, fretted neck, flat wooden soundboard, ribs, and a flat back, most often with incurved sides." The term is used to refer to a number of that were developed and used across Europe, beginning in the 12th century and, later, in the Americas. A 3,300-year-old stone carving of a Hittites bard playing a stringed instrument is the oldest iconographic representation of a chordophone, and clay plaques from Babylonia show people playing a lute-like instrument which is similar to the guitar.
Several scholars cite varying influences as antecedents to the modern guitar. Although the development of the earliest "guitar" is lost to the history of medieval Spain, two instruments are commonly claimed as influential predecessors: the four-string oud and its precursor, the European lute; the former was brought to Iberia by the Moors in the 8th century. It has often been assumed that the guitar is a development of the lute, or of the ancient Greek kithara. However, many scholars consider the lute an offshoot or separate line of development which did not influence the evolution of the guitar in any significant way. Who Invented The Acoustic Guitar?
At least two instruments called "guitars" were in use in Spain by 1200: the guitarra latina (Latin guitar) and the so-called guitarra morisca (Moorish guitar). The guitarra morisca had a rounded back, a wide fingerboard, and several sound holes. The guitarra Latina had a single sound hole and a narrower neck. By the 14th century the qualifiers "moresca" or "morisca" and "latina" had been dropped, and these two chordophones were simply referred to as guitars.Tom and Mary Anne Evans. Guitars: From the Renaissance to Rock. Paddington Press Ltd 1977 p. 16
The Spanish vihuela, called in Italian the viola da mano, a guitar-like instrument of the 15th and 16th centuries, is widely considered to have been the single most important influence in the development of the baroque guitar. It had six courses (usually), lute-like guitar tunings in fourths and a guitar-like body, although early representations reveal an instrument with a sharply cut waist. It was also larger than the contemporary four-course guitars. By the 16th century, the vihuela's construction had more in common with the modern guitar, with its curved one-piece ribs, than with the viols, and more like a larger version of the contemporary four-course guitars. The vihuela enjoyed only a relatively short period of popularity in Spain and Italy during an era dominated elsewhere in Europe by the lute; the last surviving published music for the instrument appeared in 1576.
Meanwhile, the five-course baroque guitar, which was documented in Spain from the middle of the 16th century, enjoyed popularity, especially in Spain, Italy and France from the late 16th century to the mid-18th century."The first incontrovertible evidence of five-course instruments can be found in Miguel Fuenllana's Orphenica Lyre of 1554, which contains music for a vihuela de cinco ordenes. In the following year, Juan Bermudo wrote in his Declaracion de Instrumentos Musicales: 'We have seen a guitar in Spain with five courses of strings.' Bermudo later mentions in the same book that 'Guitars usually have four strings,' which implies that the five-course guitar was of comparatively recent origin, and still something of an oddity." Tom and Mary Anne Evans, Guitars: From the Renaissance to Rock. Paddington Press Ltd, 1977, p. 24."We know from literary sources that the five course guitar was immensely popular in Spain in the early seventeenth century and was also widely played in France and Italy...Yet almost all the surviving guitars were built in Italy...This apparent disparity between the documentary and instrumental evidence can be explained by the fact that, in general, only the more expensively made guitars have been kept as collectors' pieces. During the early seventeenth century the guitar was an instrument of the people of Spain, but was widely played by the Italian aristocracy." Tom and Mary Anne Evans. Guitars: From the Renaissance to Rock. Paddington Press Ltd, 1977, p. 24. In Portugal, the word viola referred to the guitar, as guitarra meant the "Portuguese guitar", a variety of cittern.
There were many different plucked instruments that were being invented and used in Europe during the Middle Ages. By the 16th century, most of the forms of guitar had fallen off, to never be seen again. However, midway through the 16th century, the five-course guitar was established. It was not a straightforward process. There were two types of five-course guitars, differing in the location of the major third and in the interval pattern. The fifth course can be inferred because the instrument was known to play more than the sixteen notes possible with four. The guitar's strings were tuned in unison, so, in other words, it was tuned by placing a finger on the second fret of the thinnest string and tuning the guitar bottom to top. The strings were a whole octave apart from one another, which is the reason for the different method of tuning. Because it was so different, there was major controversy as to who created the five course guitar. A literary source, Lope de Vega's Dorotea, gives the credit to the poet and musician Vicente Espinel. This claim was also repeated by Nicolas Doizi de Velasco in 1640, however this claim has been contested by others who state that Espinel's birth year (1550) make it impossible for him to be responsible for the tradition. He believed that the tuning was the reason the instrument became known as the Spanish guitar in Italy. Even later, in the same century, Gaspar Sanz wrote that other nations such as Italy or France added to the Spanish guitar. All of these nations even imitated the five-course guitar by "recreating" their own.
Finally, , the form and structure of the modern guitar were developed by different Spanish makers such as Manuel de Soto y Solares and, perhaps the most important of all guitar makers, Antonio Torres Jurado, who increased the size of the guitar body, altered its proportions, and invented the breakthrough fan-braced pattern. Bracing, the internal pattern of wood reinforcements used to secure the guitar's top and back and prevent the instrument from collapsing under tension, is an important factor in how the guitar sounds. Torres' design greatly improved the volume, tone, and projection of the instrument, and it has remained essentially unchanged since.
In Mexico, the popular mariachi band includes a range of guitars, from the small Requinto guitar to the guitarrón, a guitar larger than a cello, which is tuned in the bass register. In Colombia, the traditional quartet includes a range of instruments too, from the small bandola (sometimes known as the Deleuze-Guattari, for use when traveling or in confined rooms or spaces), to the slightly larger tiple, to the full-sized classical guitar. The requinto also appears in other Latin-American countries as a complementary member of the guitar family, with its smaller size and scale, permitting more projection for the playing of single-lined melodies. Modern dimensions of the classical instrument were established by the Spaniard Antonio de Torres Jurado (1817–1892).
The original purpose of the resonator was to produce a very loud sound; this purpose has been largely superseded by guitar amplifier, but the resonator guitar is still played because of its distinctive tone. Resonator guitars may have either one or three resonator cones. The method of transmitting sound resonance to the cone is either a "biscuit" bridge, made of a small piece of hardwood at the vertex of the cone (Nationals), or a "spider" bridge, made of metal and mounted around the rim of the (inverted) cone (Dobros). Three-cone resonators always use a specialized metal bridge. The type of resonator guitar with a neck with a square cross-section—called "square neck" or "Hawaiian"—is usually played face up, on the lap of the seated player, and often with a metal or glass slide guitar. The round neck resonator guitars are normally played in the same fashion as other guitars, although slides are also often used, especially in blues.
Fender Stratocaster]]
Electric guitars can have solid, semi-hollow, or hollow bodies; solid bodies produce little sound without amplification. In contrast to a standard acoustic guitar, electric guitars instead rely on Electromagnetism pickups, and sometimes piezoelectricity pickups, that convert the vibration of the steel strings into signals, which are fed to an amplifier through a patch cable or radio transmitter. The sound is frequently modified by other electronic devices (effects units) or the natural distortion of valves () or the pre-amp in the amplifier. There are two main types of magnetic pickups, single coil- and double-coil (or humbucker), each of which can be Active pickup or Active pickup. The electric guitar is used extensively in jazz, blues, R & B, and rock and roll. The first successful magnetic pickup for a guitar was invented by George Beauchamp, and incorporated into the 1931 Ro-Pat-In (later Rickenbacker) "Frying Pan" lap steel; other manufacturers, notably Gibson, soon began to install pickups in archtop models. After World War II the completely solid-body electric was popularized by Gibson in collaboration with Les Paul, and independently by Leo Fender of Fender Music. The lower fretboard action (the height of the strings from the fingerboard), lighter (thinner) strings, and its electrical amplification lend the electric guitar to techniques less frequently used on acoustic guitars. These include tapping, extensive use of legato through and (also known as slurs), , volume swells, and use of a tremolo arm or effects pedals.
Some electric guitar models feature piezoelectricity pickups, which function as to provide a sound closer to that of an acoustic guitar with the flip of a switch or knob, rather than switching guitars. Those that combine piezoelectric pickups and magnetic pickups are sometimes known as hybrid guitars.
Hybrids of acoustic and electric guitars are also common. There are also more exotic varieties, such as guitars with two, three, or rarely four necks, all manner of alternate string arrangements, fretless guitar (used almost exclusively on bass guitars, meant to emulate the sound of a Double bass), 5.1 surround guitar, and such.
The nut is a small strip of bone, plastic, brass, corian, graphite, stainless steel, or other medium-hard material, at the joint where the headstock meets the fretboard. Its grooves guide the strings onto the fretboard, giving consistent lateral string placement. It is one of the endpoints of the strings' vibrating length. It must be accurately cut, or it can contribute to tuning problems due to string slippage or string buzz. To reduce string friction in the nut, which can adversely affect tuning stability, some guitarists fit a roller nut. Some instruments use a zero fret just in front of the nut. In this case the nut is used only for lateral alignment of the strings, the string height and length being dictated by the zero fret.
The cross-section of the neck can also vary, from a gentle "C" curve to a more pronounced "V" curve. There are many different types of neck profiles available, giving the guitarist many options. Some aspects to consider in a guitar neck may be the overall width of the fretboard, scale (distance between the frets), the neck wood, the type of neck construction (for example, the neck may be glued in or bolted on), and the shape (profile) of the back of the neck. Other types of material used to make guitar necks are graphite (Steinberger guitars), aluminum (Kramer Guitars, Travis Bean and Veleno guitars), or carbon fiber (Modulus Guitars and ThreeGuitars). Double neck electric guitars have two necks, allowing the musician to quickly switch between guitar sounds.
The neck joint or heel is the point at which the neck is either bolted or glued to the body of the guitar. Almost all acoustic steel-string guitars, with the primary exception of Taylors, have glued (otherwise known as set) necks, while electric guitars are constructed using both types.Most classical guitars have a neck and headblock carved from one piece of wood, known as a "Spanish heel".
Commonly used set neck joints include mortise and tenon joints (such as those used by C. F. Martin & Co.), dovetail joints (also used by C. F. Martin on the D-28 and similar models) and Spanish heel neck joints, which are named after the shoe they resemble and commonly found in classical guitars. All three types offer stability.
Bolt-on necks, though they are historically associated with cheaper instruments, do offer greater flexibility in the guitar's set-up, and allow easier access for neck joint maintenance and repairs. Another type of neck, only available for solid-body electric guitars, is the neck-through-body construction. These are designed so that everything from the machine heads down to the bridge is located on the same piece of wood. The sides (also known as wings) of the guitar are then glued to this central piece. Some luthiers prefer this method of construction as they claim it allows better sustain of each note. Some instruments may not have a neck joint at all, having the neck and sides built as one piece and the body built around it.
The fingerboard, also called the fretboard, is a piece of wood embedded with metal frets that comprises the top of the neck. It is flat on classical guitars and slightly curved crosswise on acoustic and electric guitars. The curvature of the fretboard is measured by the fretboard radius, which is the radius of a hypothetical circle of which the fretboard's surface constitutes a segment. The smaller the fretboard radius, the more noticeably curved the fretboard is. Most modern guitars feature a 12" neck radius, while older guitars from the 1960s and 1970s usually feature a 6–8" neck radius. Pinching a string against a fret on the fretboard effectively shortens the vibrating length of the string, producing a higher pitch.
Fretboards are most commonly made of rosewood, ebony, maple, and sometimes manufactured using composite materials such as HPL or resin. See the section "Neck" below for the importance of the length of the fretboard in connection to other dimensions of the guitar. The fingerboard plays an essential role in the treble tone for acoustic guitars. The quality of vibration of the fingerboard is the principal characteristic for generating the best treble tone. For that reason, ebony wood is better, but because of high use, ebony has become rare and extremely expensive. Most guitar manufacturers have adopted rosewood instead of ebony.
The ratio of the spacing of two consecutive frets is (twelfth root of two). In practice, luthiers determine fret positions using the constant 17.817—an approximation to 1/(1-1/). If the nth fret is a distance x from the bridge, then the distance from the (n+1)th fret to the bridge is x-(x/17.817). Frets are available in several different gauges and can be fitted according to player preference. Among these are "jumbo" frets, which have a much thicker gauge, allowing for use of a slight vibrato technique from pushing the string down harder and softer. "Scalloped" fretboards, where the wood of the fretboard itself is "scooped out" between the frets, allow a dramatic vibrato effect. Fine frets, much flatter, allow a very low string-action, but require that other conditions, such as curvature of the neck, be well-maintained to prevent buzz.
Adjusting the truss rod affects the intonation of a guitar as well as the height of the strings from the fingerboard, called the action. Some truss rod systems, called double action truss systems, tighten both ways, pushing the neck both forward and backward (standard truss rods can only release to a point beyond which the neck is no longer compressed and pulled backward). The artist and luthier Irving Sloane pointed out, in his book Steel-String Guitar Construction, that truss rods are intended primarily to remedy concave bowing of the neck, but cannot correct a neck with "back bow" or one that has become twisted. Classical guitars do not require truss rods, as their nylon strings exert a lower tensile force with lesser potential to cause structural problems. However, their necks are often reinforced with a strip of harder wood, such as an ebony strip that runs down the back of a Thuja plicata neck. There is no tension adjustment on this form of reinforcement.
Dots are usually inlaid into the upper edge of the fretboard in the same positions, small enough to be visible only to the player. These usually appear on the odd-numbered frets, but also on the 12th fret (the one-octave mark) instead of the 11th and 13th frets. Some older or high-end instruments have inlays made of mother of pearl, abalone, ivory, colored wood or other exotic materials and designs. Simpler inlays are often made of plastic or painted. High-end classical guitars seldom have fretboard inlays as a well-trained player is expected to know their way around the instrument. In addition to fretboard inlay, the headstock and soundhole surround are also frequently inlaid. The manufacturer's logo or a small design is often inlaid into the headstock. Rosette designs vary from simple concentric circles to delicate fretwork mimicking the historic rosette of lutes. Bindings that edge the finger and soundboards are sometimes inlaid. Some instruments have a filler strip running down the length and behind the neck, used for strength or to fill the cavity through which the truss rod was installed in the neck.
In an acoustic instrument, the body of the guitar is a major determinant of the overall sound quality. The guitar top, or soundboard, is a finely crafted and engineered element made of such as spruce and Thuja plicata. This thin piece of wood, often only 2 or 3 mm thick, is strengthened by differing types of Guitar bracing. Many luthiers consider the top the dominant factor in determining the sound quality. The majority of the instrument's sound is heard through the vibration of the guitar top as the energy of the vibrating strings is transferred to it. The body of an acoustic guitar has a sound hole through which sound projects. The sound hole is usually a round hole in the top of the guitar under the strings. The air inside the body vibrates as the guitar top and body is vibrated by the strings, and the response of the air cavity at different frequencies is characterized, like the rest of the guitar body, by a number of resonance modes at which it responds more strongly.
The top, back and ribs of an acoustic guitar body are very thin (1–2 mm), so a flexible piece of wood called lining is glued into the corners where the rib meets the top and back. This interior reinforcement provides 5 to 20 mm of solid gluing area for these corner joints. Solid linings are often used in classical guitars, while kerfed lining is most often found in steel-string acoustics. Kerfed lining is also called kerfing because it is scored, or "kerfed"(incompletely sawn through), to allow it to bend with the shape of the rib). During final construction, a small section of the outside corners is carved or routed out and filled with binding material on the outside corners and decorative strips of material next to the binding, which is called purfling. This binding serves to seal off the end grain of the top and back. Purfling can also appear on the back of an acoustic guitar, marking the edge joints of the two or three sections of the back. Binding and purfling materials are generally made of either wood or plastic.
Body size, shape and style have changed over time. 19th-century guitars, now known as salon guitars, were smaller than modern instruments. Differing patterns of internal bracing have been used over time by luthiers. Torres, Hauser, Ramirez, Fleta, and C. F. Martin were among the most influential designers of their time. Bracing not only strengthens the top against potential collapse due to the stress exerted by the tensioned strings but also affects the resonance characteristics of the top. The back and sides are made out of a variety of timbers such as mahogany, Indian rosewood and highly regarded Brazilian rosewood ( Dalbergia nigra). Each one is primarily chosen for their aesthetic effect and can be decorated with inlays and purfling.
Instruments with larger areas for the guitar top were introduced by Martin in an attempt to create greater volume levels. The popularity of the larger "dreadnought" body size amongst acoustic performers is related to the greater sound volume produced.
Most electric guitar bodies are made of wood and include a plastic pickguard. Boards wide enough to use as a solid body are very expensive due to the worldwide depletion of hardwood stock since the 1970s, so the wood is rarely one solid piece. Most bodies are made from two pieces of wood with some of them including a seam running down the center line of the body. The most common woods used for electric guitar body construction include maple, Tilia americana, Fraxinus, Populus, alder, and mahogany. Many bodies consist of good-sounding, but inexpensive woods, like ash, with a "top", or thin layer of another, more attractive wood (such as maple with a natural "flame" pattern) glued to the top of the basic wood. Guitars constructed like this are often called "flame tops". The body is usually carved or routed to accept the other elements, such as the bridge, pickup, neck, and other electronic components. Most electrics have a polyurethane or nitrocellulose lacquer finish. Other alternative materials to wood are used in guitar body construction. Some of these include carbon composites, plastic material, such as polycarbonate, and aluminum alloys.
On almost all modern electric guitars, the bridge has saddles that are adjustable for each string so that intonation stays correct up and down the neck. If the open string is in tune, but sharp or flat when frets are pressed, the bridge saddle position can be adjusted with a screwdriver or hex key to remedy the problem. In general, flat notes are corrected by moving the saddle forward and sharp notes by moving it backward. On an instrument correctly adjusted for intonation, the actual length of each string from the nut to the bridge saddle is slightly, but measurably longer than the scale length of the instrument. This additional length is called compensation, which flattens all notes a bit to compensate for the sharping of all fretted notes caused by stretching the string during fretting.
Traditional electromagnetic pickups are either single-coil or double-coil. Single-coil pickups are susceptible to noise induced by stray electromagnetic fields, usually mains-frequency (60 or 50 hertz) hum. The introduction of the double-coil humbucker in the mid-1950s solved this problem through the use of two coils, one of which is wired in opposite polarity to cancel or "buck" stray fields.
The types and models of pickups used can greatly affect the tone of the guitar. Typically, humbuckers, which are two magnet-coil assemblies attached to each other, are traditionally associated with a heavier sound. Single-coil pickups, one magnet wrapped in copper wire, are used by guitarists seeking a brighter, twangier sound with greater dynamic range.
Modern pickups are tailored to the sound desired. A commonly applied approximation used in the selection of a pickup is that less wire (lower electrical impedance) gives a brighter sound, more wire gives a "fat" tone. Other options include specialized switching that produces coil-splitting, in/out of phase and other effects. Guitar circuits are either active, needing a battery to power their circuit, or, as in most cases, equipped with a passive circuit.
Fender Stratocaster-type guitars generally have three single-coil pickups, while most Gibson Les Paul types have humbucker pickups.
Piezoelectric, or piezo, pickups represent another class of pickup. These employ piezoelectricity to generate the musical signal and are popular in hybrid electro-acoustic guitars. A crystal is located under each string, usually in the saddle. When the string vibrates, the shape of the crystal is distorted, and the stresses associated with this change produce tiny voltages across the crystal that can be amplified and manipulated. Piezo pickups usually require a powered pre-amplifier to lift their output to match that of electromagnetic pickups. Power is typically delivered by an on-board battery.
Most pickup-equipped guitars feature onboard controls, such as volume or tone, or pickup selection. At their simplest, these consist of passive components, such as and , but may also include specialized integrated circuits or other active components requiring batteries for power, for preamplification and signal processing, or even for electronic tuner. In many cases, the electronics have some sort of shielding to prevent pickup of external interference and noise.
Guitars may be shipped or retrofitted with a hexaphonic pickup, which produces a separate output for each string, usually from a discrete piezoelectric or magnetic pickup. This arrangement lets on-board or external electronics process the strings individually for modeling or MIDI (MIDI) conversion. Roland makes "GK" hexaphonic pickups for guitar and bass, and a line of guitar modeling and synthesis products. Line 6's hexaphonic-equipped Variax guitars use on-board electronics to model the sound after various vintage instruments, and vary pitch on individual strings.
MIDI converters use a hexaphonic guitar signal to determine pitch, duration, attack, and decay characteristics. The MIDI sends the note information to an internal or external sound bank device. The resulting sound closely mimics numerous instruments. The MIDI setup can also let the guitar be used as a game controller (i.e., Rock Band Squier) or as an instructional tool, as with the Fretlight Guitar.
The pitches are as follows:
| 329.63 |
| 246.94 |
| 196.00 |
| 146.83 |
| 110.00 |
| 82.41 |
The table below shows a pitch's name found over the six strings of a guitar in standard tuning, from the nut (zero), to the twelfth fret.
For four strings, the 5th fret on one string is the same open-note as the next string; for example, a 5th-fret note on the sixth string is the same note as the open fifth string. However, between the second and third strings, an irregularity occurs: The 4th-fret note on the third string is equivalent to the open second string.
Open tuning refers to a guitar tuned so that strumming the open strings produces a chord, typically a major chord. The base chord consists of at least 3 notes and may include all the strings or a subset. The tuning is named for the open chord, Open D, open G, and open A are popular tunings. All similar chords in the chromatic scale can then be played by barre chord a single fret. Open tunings are common in blues and folk music, and they are used in the playing of slide guitar and bottleneck guitars. Many musicians use open tunings when playing slide guitar. Ry Cooder plays slide-guitar with open tunings.
For the standard tuning, there is exactly one interval of a major third between the second and third strings, and all the other intervals are fourths. The irregularity has a price – chords cannot be shifted around the fretboard in the standard tuning E-A-D-G-B-E, which requires four chord-shapes for the major chords. There are separate chord-forms for chords having their root note on the third, fourth, fifth, and sixth strings.
In contrast, regular tunings have equal intervals between the strings, and so they have symmetrical scales all along the fretboard. This makes it simpler to translate chords. For the regular tunings, chords may be moved diagonally around the fretboard. The diagonal movement of chords is especially simple for the regular tunings that are repetitive, in which case chords can be moved vertically: Chords can be moved three strings up (or down) in major-thirds tuning and chords can be moved two strings up (or down) in augmented-fourths tuning. Regular tunings thus appeal to new guitarists and also to jazz-guitarists, whose improvisation is simplified by regular intervals.
On the other hand, some chords are more difficult to play in a regular tuning than in standard tuning. It can be difficult to play conventional chords, especially in augmented-fourths tuning and all-fifths tuning, in which the large spacings require hand stretching. Some chords, which are conventional in folk music, are difficult to play even in all-fourths and major-thirds tunings, which do not require more hand-stretching than standard tuning.
Another class of alternative tunings is called drop tunings, because the tuning drops down the lowest string. Dropping down the lowest string a major second results in the "drop-D" (or "dropped D") tuning. Its open-string notes DADGBE (from low to high) allow for a deep bass D note, which can be used in keys such as D major, d minor and G major. It simplifies the playing of simple fifths (). Many contemporary rock bands re-tune all strings down, making, for example, Drop-C or Drop-B tunings.
Picks come in many shapes and sizes. Picks vary from the small jazz pick to the large bass pick. The thickness of the pick often determines its use. A thinner pick (between 0.2 and 0.5 mm) is usually used for strumming or rhythm playing, whereas thicker picks (between 0.7 and 1.5+ mm) are usually used for single-note lines or lead playing. The distinctive guitar sound of Billy Gibbons is attributed to using a quarter or peso as a pick. Similarly, Brian May is known to use a sixpence coin as a pick, while noted 1970s and early 1980s session musician David Persons is known for using old credit cards, cut to the correct size, as plectrums.
Thumb picks and finger picks that attach to the fingertips are sometimes employed in finger-picking styles on steel strings. These allow the fingers and thumb to operate independently, whereas a flat pick requires the thumb and one or two fingers to manipulate.
The lower strap button is usually located at the bottom (bridge end) of the body. The upper strap button is usually located near or at the top (neck end) of the body: on the upper body curve, at the tip of the upper "horn" (on a double cutaway), or at the neck joint (heel). Some electrics, especially those with odd-shaped bodies, have one or both strap buttons on the back of the body. Some Steinberger electric guitars, owing to their minimalist and lightweight design, have both strap buttons at the bottom of the body. Rarely, on some acoustics, the upper strap button is located on the headstock. Some acoustic and classical guitars only have a single strap button at the bottom of the body—the other end must be tied onto the headstock, above the nut and below the machine heads.
|
|
